Máy đo độ ồn và phân tích dải tần Norsonic Nor139

Máy đo độ ồn và phân tích dải tần Nor139Máy đo độ ồn và phân tích dải tần Nor139
Máy đo âm thanh và phân tích dải tần Nor139Máy đo âm thanh và phân tích dải tần Nor139
Máy đo độ ồn và phân tích dải tần Nor139Máy đo độ ồn và phân tích dải tần Nor139

Máy đo độ ồn và phân tích dải tần Norsonic Nor139

• Hãng sản xuất

Model

Bảo hành

Norsonic

Nor139

12 tháng

Để có giá tốt nhất và nhanh nhất, vui lòng liên hệ

(028) 3977 8269 – (028) 3601 6797

Email: sales@lidinco.com – lidinco@gmail.com

  • Mô tả
  • Thông số kỹ thuật
  • Tùy chọn thêm

Mô tả

Giới thiệu máy đo độ ồn và phân tích dải tần Nor139

Các ứng dụng

– Phân tích tiếng ồn và dải tần
– Ghi lại mức độ ồn
– Nhận dạng nguồn tiếng ồn
– Đo tiếng ồn theo HVAC
– Phân tích tiếng ồn ở nơi làm việc
– Giám sát độ ồn của khu vực từ xa
– Phát hiện lỗi và phát triển sản phẩm dựa vào phân tích âm thanh
– Đo mức âm thanh đa năng

Tính năng

– Precision integrating sound level meter to IEC 61672 class 1
– Handheld real-time 1/1-octave or 1/3-octave frequency analyser (6,3Hz-20kHz)
– Measurement of A-weighted levels simultaneously with either C- or Z-weighted levels
– Parallel detection of SPL, Leq, Lmin, Lmax, LE and Lpeak 120 dB dynamic range giving a “one-range” instrument
– Measures Lpeak levels up to 140 dB
– Parallel detection of F, S and I time constants
– USB 2.0 and High-speed RS-232 serial interface
– SD memory card and large high speed internal memory
– Sound recording in 8, 16 or 24 bit format with 12 or 48 kHz sampling
– Up to 90 sec. audio recording pretrigger
– High-resolution graphical backlit display
– Manual or automatic storage of results
– Automatically repeated measurements with clock synchronization
– Pause/Continue function with back erase feature
– Results displayed as dB or linear values
– Numerical printouts
– AC output signal
– Windscreen correction
– Support for IEPE sensors
– NC, NR and RC rating
– Multiple language selection
– Moving Leq

Tham khảo thêm sản phẩm khác tại: Danh mục máy đo độ ồn

Analouge inputs

Input connector: TNC connector for Norsonic microphone systems.
Preamplifier: Nor1207 IEPE.
Polarisation voltage: 0 V (pre-polarized)
Supply current: 3mA
Supply voltage: 24V
Input impedance: > 100 kohm, <650 pF
Measurement range: 0.3 mV to 7 V (RMS) in one range corresponding to –10 dB to 137 dB with a microphone sensitivity of 50 mV/Pa. The maximum peak value ±10 V corresponds to 140 dB.
Microphone: Nor1228

Measurement range

0,3 µV – 7Vrms (10 Vpeak) in one range corresponding to -10 dB to 137 dB (140 dB peak) with a microphone sensitivity of 50mV/Pa. Option 18 shifts the measurement range to 147 dB (150 dB peak) by reducing the microphone sensitivity

Highpass filter

The input section is equipped with an analogue highpass filter to reduce noise from wind or other sources with frequencies below the frequency range for measurements. The filter is switched on if the limited frequency range is selected (>6,3 Hz).
Filter type: 3rd order HP filter (-3 dB at 3,4 Hz, Butterworth response)

Analogue to digital conversion

The analogue input signal is converted to a digital signal by a multirange sigma-delta converter with an effective sampling frequency of 48 kHz. The anti-aliasing filter is a combination of an analogue and a digital filter.

Frequency weightings

Simultaneous measurement of A and C-weighting or A- and Z-weighting. 1/1 octave band or 1/3 octave band levels may be measured simultaneously if options providing these weightings are installed.
1/1 octave filters: 0,5 – 16000 Hz, class 1, digital IIR filters, base 10 system (IEC 61260) and ANSI S1.11- 2004 Class 1.
1/3 octave filters: 0,4 – 20000 Hz, class 1, digital IIR filters, base 10 system (IEC 61260) and ANSI S1.11- 2004 Class 1.

Level detector

Detector type: Digital true rootmean-square (RMS) detection, resolution 0.1 dB which may optionally be increased to 0.01 dB for indicated levels in the range –9.99 to 99.99 dB.
Crest factor capability: The crest factor is only limited by the peak-value of the signal.
Simultaneous measurement of the following functions: SPL, Lmax; Lmin; Leq; LE; Lpeak; LN; LeqI; LEI; LTMax5

Indication range

The calibration of the instrument allows microphones with sensitivity in the range -84 dB to +15.9 dB relative to 1V/Pa to be applied. The corresponding display range for the indicated sound level is -50 dB to +180 dB

Self-noise levels

The self-noise is measured with the calibration set to –26.0 dB corresponding to a microphone sensitivity of 50mV/Pa. For voltage input, the level 0 dB then corresponds to 1µV. Typical values for the self-noise are 5 dB lower than the values stated.

Noise measured with 18 pF microphone dummy and microphone preamplifier Nor1209, averaged over 30 s of measurement time:
A-weighted: 13 dB
C-weighted: 15 dB
Z-weighted: 25 dB
1/3 oct: 6.3 Hz to 250 Hz: 10 dB
1/3 oct: 315 Hz to 20 kHz: 5 dB

Noise measured with Nor1225 microphone and preamplifier Nor1209, averaged over 30 s of measurement time:
A-weighted: 18 dB
C-weighted: 22 dB
Z-weighted: 30 dB
1/3 oct: 6.3 Hz to 250 Hz: 15 dB
1/3 oct: 315 Hz to 20 kHz: 10 dB

Power supply

Batteries: 4 cells, IEC LR6, AA-sized
Typical battery life time: up to 14 hours

External DC: 11 – 16V. Power consumption approximately 1.2W depending on selected modes of operation. The mains adapter Nor340 is recommended for use with the instrument. If the external supply falls below 9V, the instrument will use the internal batteries if available. If the instrument switched itself off due to loss of power, it will automatically switch on and resume normal operation after reapplying the external DC supply.

Display

The display is a monochrome, transreflective LCD graphical display with 160×240 pixels (W×H) with automatic temperature compensation for contrast and viewing angle. Pressing the light key illuminates the display. The light switches off automatically
two minutes after the last operation of any key. The bargraph display covers 80 dB which may be scrolled in 10 dB steps to cover the total range.

Signal generator output

Max output voltage: ±10V
Output impedance: <100Ωohm. The output is short-circuit proof to GND and output current is in excess of 3 mA.
Gain accuracy at 1 kHz: ±0.2 dB
Frequency response re. 1 kHz: ±0.5 dB for 20 Hz < f< 20 kHz
AC-out: 3,5 mm stereo jack. Both channels have identical signals driven by two separate amplifiers. Load impedance shall be 16 ohm or more. Output voltage is generated by the 48 kHz DAC based on data from DSP. Full scale on the display bargraph corresponds to 100 mV.
Output impedance: Less than 10 ohm, AC-coupled 100 µF.
Gain accuracy 1 kHz: ±0,2 dB
Frequency response re. 1 kHz: ±0,5 dB for 20 Hz < f < 20 kHz.

USB interface: USB type 2.0
USB socket: B411
Serial I/O port: RS232 port, 9600 – 115200 baud.

Digital inputs: 3
Digital outputs: 4

SD Memory Card

The instrument may use SD memory card for storing of setup information, sound recordings and measurement results. SD memory card included in the delivery.

Environmental condition for operation

Temperature: –10°C to +50°C
Humidity: 5% to 90% RH, dewpoint less than 40°C.
Atmospheric pressure: 85 kPa to 108 kPa.

Environmental conditions for storage

Temperature: –30°C to +60°C
Humidity: 5% to 90% RH, dewpoint less than 40°C.
Atmospheric pressure: 50 kPa to 108 kPa.

Dimensions

Depth: 30 mm
Width: 75 mm
Weight incl. batteries: 410 g
Length, excl.microphone/preamplifier: 210 mm
Length, incl. microphone/preamplifier: 292 mm

The Nor139 environmental noise meter may be extended with a selection of optional features that may be ordered and installed at any time.

Option packages:
All package containing the basic Nor139 with the options 1, 3, 4, 5, 6, 7, 8 and 16
Environmental package containing the basic Nor139 with the options 4, 5, 6, 7, 8 and 16.

Option 1: 1/1-octave real-time filters
Option 3: 1/3-octave real-time filters
Option 4: Statistical calculation of LN values
Option 5: Parallel F, S and I time weightings
Option 6: Level versus time measurement
Option 7: Advanced Level versus time measurements
Option 8: Sound recording
Option 16: Trigger