Máy phát xung Pulse PSPL10300B Tektronix

may-phat-xung-pulse-pspl10300b-tektronix

Máy phát xung Pulse PSPL10300B Tektronix

  •  Hãng sản xuất: Tektronix
  •  Model: PSPL10000B
  •  Bảo hành: 12 tháng

Để có giá tốt nhất và nhanh nhất, vui lòng liên hệ

(08) 3977 8269 – (08) 3601 6797

Email: sales@lidinco.com – lidinco@gmail.com

  • Mô tả
  • Thông tin bổ sung
  • Thông số kỹ thuật

Mô tả

Máy phát xung Pulse PSPL10300B từ hãng Tektronix ( Mỹ)  với bảng điều khiển phía trước giúp thuận tiện hơn trong quá trình điều khiển hoặc kết nối với máy tính. Đảm bảo  hình dạng tín hiệu phù hợp với tất cả các thiết lập.

may-phat-xung-pulse-pspl10300b-tektronixCác thông số quan trọng

  • Positive or negative polarity pulses
  • Adjustable positive pulse amplitude from < 5 mV to 50 V
  • Rise time 300 ps
  • Adjustable duration from < 1 ns to 100 ns
  • Single shot, or 1 Hz to 100 kHz repetition rate

Các chức năng chính:

  • Keypad interface
  • Programmable IEEE-488 
  • Internal, external, manual or GPIB trigger modes
  • Gated output
  • Port for external baseline offset up to ±50 V

Các Ứng Dụng

  • University education and research
  • UWB signal source
  • Semiconductor characterization
  • Laser driver

Hiệu suất tiêu biểu

15 V/div and 500 ps/div. Adjustable amplitude from -45 V to +50 V in 1 dB steps. Also adjustable baseline offset from -5 V to +5 V.

8 V/div and 1 ns/div. Adjustable duration from < 1 ns to 100 ns in 25 ps steps.

8 V/div and 200 ps/div. Leading edge 250 ps rise time.

20 V/div and 20 ns/div. 20 ns and 100 ns pulses.

Thông tin bổ sung

Hãng SX

Tektronix

Parameter Value
Polarity Positive or negative
Amplitude into 50 Ω (See Notes) 4.5 mV to 50 V positive, -4 mV to -45 V negative, adjustable in 1 dB steps
Amplitude accuracy, into 50 Ω (full output amplitude) ±2 V positive, ±3 V negative
Baseline Adjustable from -5 V to +5 V in 1.25 mV steps, external input provided for user-supplied offset of ±50 V
Transition time, leading edge (10 – 90%) 300 ps, 325 ps max.
Transition time, trailing edge (10 – 90%) 750 ps, 1 ns max.
Reflection coefficient 30% during pulse, +50% after pulse, improves with increasing attenuation
Source impedance (nominal) 50 Ω
Duration (FWHM) (See Notes) < 1 ns to 100 ns, adjustable in 25 ps steps
Baseline precursor < ±1%
Topline overshoot 2%
Topline perturbations ±1% for t < 3 ns (±2% for negative pulse)
Topline flatness ±0.5% for t > 3 ns (±2% for negative pulse)
Spurious pulse at 120 ns +6% with pulse duration ≤ 20 ns, +30% for pulse duration = 100 ns

Notes:

The duration and delay values displayed on the front panel LCD and programmed over GPIB are only to be considered “nominal” values and not absolute values. The duration and delay parameters exhibit some thermal drift, rep rate dependency and interaction. There will be some loss in amplitude at minimum pulse durations. The amplitude tolerance of ±2 V holds only for > 10 ns durations. The amplitude has a minor rep rate dependency. Always use an oscilloscope as an independent check of these pulse parameters. The instrument is adjusted and calibrated at the factory in an ambient temperature of 23 °C (±3 °C) at a rep. rate of 100 kHz. The instrument will operate over a temperature range of 0 to 50 °C but will not meet all specifications over this range.

Trigger and timing

The performance parameters listed in this table are typical values; parameters are guaranteed only when maximum and/or minimum limits are given.

Parameter Value
Trigger in/out delay 185 ns
Repetition rate 1 Hz to 100 kHz
Period 10 µs to 1 s, 0.1 µs steps
Trigger mode Internal, external, manual, or GPIB
External trigger input level -2 to +2 V, 1 mV steps, positive or negative slope
Maximum external trigger input ±5 V
External trigger impedance 50 Ω
Trigger output into 50 Ω 1 V, 1 µs
Delay (See Notes above) 0 to 100 ns, 25 ps steps
Delay jitter, RMS < 10 ps
External gate input TTL, > 2 V on, < 0.5 V off
External gate impedance 50 Ω
General specifications
Parameter Description
Accessories included Power cord, BNC cable, rack mount kit, instruction manual
Front panel controls Power, menu, data entry, disable/enable, local, and manual trigger
Power supply (mains) 100, 115, or 230 VAC, ±10% switch selectable, 50 or 60 Hz
Power consumption 48 VA (60 Hz), 65 VA (50 Hz)
Operating environment (See Notes above)
   Temperature 40 °C (104 °F); low limit of 0 °C (32 °F)
   Humidity 80% for temperatures up to 31 °C (88 °F), decreasing linearly to 50% at 40 °C (104 °F)
   Elevation 2000 m (6562 ft.)
Dimensions 19.0 x 15.2 x 5.5 in. (48.3 x 38.6 x 14.0 cm)
Weight 21 lbs (9.5 kg)
Connectors SMA output, BNC trig in, gate in, trig out, BNC on rear panel for baseline offset d/a output and bias tee input, GPIB on rear panel
GPIB standard IEEE-488.1-1987 
GPIB interface functions SH1, AH1, T6, L4, SR1, RL1, PPO, DC1, DT1, CO and E2
Set up Save/recall in 10 memories with battery backup
Warranty One year