Máy phát xung Pulse PSPL10050A Textronix

may-phat-xung-pulse-seri-pspl10000-textronix

Máy phát xung Pulse PSPL10050A Textronix

• Hãng sản xuất

Model

Bảo hành

Tektronix

PSPL10050A

12 tháng

Để có giá tốt nhất và nhanh nhất, vui lòng liên hệ

(08) 3977 8269 – (08) 3601 6797

Email: sales@lidinco.com – lidinco@gmail.com

  • Mô tả
  • Thông tin bổ sung
  • Thông số kỹ thuật

Mô tả

Máy phát xung Pulse PSPL10050A cao cấp nhập khẩu từ Textronix  Mỹ đảm bảo dạng tín hiệu chuẩn xác phù hợp với mọi thiết lập.

may-phat-xung-pulse-seri-pspl10000-textronixCác thông số kỹ thuật chính

  • Pulse amplitudes from 7.5 to 10 V
    • 10 V fixed amplitude, PSPL10050A
    • 900 µV to 10 V, PSPL10060A
    • 700 µV to 7.5 V, PSPL10070A
  • Rise times from 65 ps down to 45 ps
  • Adjustable duration from 100 ps to 10 ns
  • Single shot, or 1 Hz to 100 kHz repetition rate

Chức năng chính

  • Keypad interface
  • Programmable IEEE-488
  • Internal, external, manual, or GPIB trigger modes
  • Gated output

Các ứng dụng

  • University education and research
  • UWB signal source
  • Semiconductor characterization
  • Laser driver

Typical performance

Rise time for the PSPL10050A at 2 V/div and 20 ps/div

Adjustable duration for the PSPL10050A at 2 V/div and 200 ps/div

Rise time for the PSPL10060A at 2 V/div and 20 ps/div

Adjustable duration for the PSPL10060A at 2 V/div and 100 ps/div

Rise time for the PSPL10070A at 1.2 V/div and 20 ps/div

Adjustable duration for the PSPL10070A at 1.2 V/div and 200 ps/div

Thông tin bổ sung

Hãng SX

Tektronix

Các thông số được ghi trong bảng dưới đây là các giá trị tiêu biểu.Các thông số đảm bảo trong vùng giới hạn

Parameter PSPL10050A PSPL10060A PSPL10070A
Amplitude into 50 Ω(See Notes) 10 V (fixed) 900 μV to 10 V, adjustable in 1 dB steps ±700 μV to ±7.5 V, adjustable in 1 dB steps
Amplitude accuracy, into 50 Ω ± 0.2 V
Polarity Positive only Positive only Positive or negative
Baseline 0 V 0 V -5 V to +5 V in 1.25 mV steps
Transition time, leading edge
(10 – 90%)
(20 – 80%)
≤45 ps typ, ≤55 ps max
---
≤55 ps typ, ≤65 ps max
---
≤65 ps typ, ≤75 ps max
≤40 ps typ, ≤50 ps max
Transition time, trailing edge
(10 – 90%)
(20 – 80%)
≤110 ps typ, ≤130 ps max
---
≤115 ps typ
---
---
≤80 ps typ ≤100 ps max
Reflection coefficient ±5% during pulse +80%, -40% after pulse ±5% during pulse +80%, -40% after pulse
(improves with increasing atten.)
50% @ 0 dB (7.5 V) 20% @ 6 dB (3.7 V)
-10 % @ > 10 dB (< 2.3 V)
Source impedance (nominal) 50 Ω
Duration (FWHM) (See Notes) 100 ps to 10 ns in 2.5 ps steps
Baseline precursor < 1%
Topline overshoot < 4%
Topline perturbations < ±3% for t < 2 ns
Topline flatness < ±0.5% for 2 ns < t < 10 ns

Notes:

The duration and delay values displayed on the front panel LCD and programmed over the GPIB are only to be considered “nominal” values and not absolute values. The duration and delay parameters do exhibit some thermal drift, rep rate dependency and interaction. There will be some loss in amplitude at minimum pulse durations. The amplitude tolerance of ±0.2 V holds only for > 2 ns durations. Always use an oscilloscope as an independent check of these pulse parameters. The instrument is adjusted and calibrated at the factory in an ambient temperature of 23 °C (±3 °C) at a rep. rate of 100 kHz. The instrument will operate over a temperature range of 0 to 50 °C but will not meet all specifications over this range.

Trigger and timing

The performance parameters listed in this table are typical values; parameters are guaranteed only when maximum and/or minimum limits are given.

Parameter PSPL10050A PSPL10060A PSPL10070A
Trigger in/out delay 90 ns 90 ns 100 ns
Repetition rate 1 Hz to 100 kHz
Period 10 µs to 1 s, 0.1 µs steps
Trigger mode Internal, external, manual, or GPIB
External trigger input level -2 to +2 V, 1 mV steps, positive or negative slope
Maximum external trigger input ±5 V
External trigger impedance 50 Ω
Trigger output into 50 Ω 2.4 V, 50 ns
Delay (See Notes above) 0 to 63 ns, 1 ns steps
Delay jitter, RMS 1.5 ps
External trigger jitter, RMS 5 ps (<1 ns rise)
External gate input TTL, >2 V on, <0.5 V off
External gate impedance 50 Ω
Thông số chung
Parameter PSPL10050A PSPL10060A PSPL10070A
Accessories included Remote Pulse Head & 4 ft coaxial cable, power cord, rack mount kit, instruction manual Power cord, rack mount kit, instruction manual Power cord, rack mount kit, instruction manual
Controls Power, menu, data entry, disable/enable, local and manual trigger
Power supply (mains) 100, 115, or 230 VAC, ±10% switch selectable, 50 or 60 Hz
Power consumption 48 VA (60 Hz), 65 VA (50 Hz)
Operating environment (See Notes above)
   Temperature 40 °C (104 °F); low limit of 0 °C (32 °F)
   Humidity 80% for temperatures up to 31 °C (88 °F), decreasing linearly to 50% at 40 °C (104 °F)
   Elevation 2000 m (6562 ft.)
Dimensions 19.0 x 15.2 x 5.5 in. (48.3 x 38.6 x 14.0 cm)
Weight 21 lbs (9.5 kg)
Connectors SMA output, BNC trig in, gate in, trig out, GPIB on rear panel
GPIB standard IEEE-488.1-1987
GPIB interface functions SH1, AH1, T6, L4, SR1, RL1, PPO, DC1, DT1, CO and E2.
Set up Save/recall in 10 memories with battery back up
Warranty One year